MikroTik Script: No-IP.com DDNS Update

I've been using No-IP.com as my Dynamic DNS service for the past year. I was keeping my DDNS address updated via No-IP's  Dynamic Update Client for Windows. Using No-IP's client to keep the DDNS address and IP current worked well, but I wanted to move the update functionality from my home PC to my MikroTik. There was already a script for this on the MikroTik Wiki that was created by riverron, which I had tried, but I wanted to make a few minor modifications to the script. I converted the scope of the variable $previousIP from global to local and assigned the value to this variable via DNS resolution. I also added a variable to set the log destination, which is fetched from No-IP's DDNS service when an update occurs.

Marthur's No-IP.com Dynamic DNS Update Script v1.0

#---------------------------------------------------SCRIPT INFORMATION----------------------------------------------------
# Script:  Marthur's No-IP.com Dynamic DNS Update Script
# Version: 1.0
# Updated: 10/21/2017
# Created: 10/21/2017
# Author:  Marthur Jones
# Website: https://www.marthur.com
# This script is to be used in conjunction with No-IP.com's Dynamic DNS Service. It is to be scheduled/ran on a Mikrotik 
# router as replacement for No-IP's Dynamic Update Client for Windows. There are many versions of this script. However, 
# I've made my own modifications to the original script that was created on March 13, 2012 by riverron and published on
# the MikroTik Wiki here:
# https://wiki.mikrotik.com/wiki/Dynamic_DNS_Update_Script_for_No-IP_DNS
# - Changed the scope of the variable that stores the previous IP address from global to local. The local variable's value 
#   (IP address) is now assigned via MikroTik's DNS resolution. The script compares the previous IP with the current IP 
#   that is assigned to the WAN interface, if the IP addresses do not match, the script will update the No-IP hostname
#   with the IP assigned to the WAN interface.
# - Added variable to define the log destination path that the script pulls from No-IP.com after a DDNS IP update.
# - Made variable name changes.
#-----------------------------------------------TESTED USING THE FOLLOWING------------------------------------------------
# Hardware: CCR1009-7G-1C-1S+
# Firmware: v3.41
# RouterOS: v6.40.4
#----------------------------------------------MODIFY THIS SECTION AS NEEDED----------------------------------------------

# No-IP account credentials.
:local noipUsername "NOIP_USERNAME"
:local noipPassword "NOIP_PASSWORD"

# Set the hostname or label of network to be updated.
# Hostnames with spaces are unsupported. Replace the value in the quotations below with your host names.
# To specify multiple hosts, separate them with commas.
:local noipHostname "NOIP_HOSTNAME.ddns.net"

# The interface name with the assigned dynamic IP address (usually the WAN interface).
:local wanInterface "Ether0-Gateway"

# Log destination
:local logDestination "/disk1/logs/"


:log warning message="START: No-IP DDNS Update"

:if ([/interface get wanInterface value-name=running] = true) do={

#   Get the previous IP via DNS resolution.
    :local previousIP [:resolve "$noipHostname"]

#   Get the current IP on the WAN interface.
    :local currentIP [/ip address get [find interface="$wanInterface" disabled=no] address]

#   Strip net mask from IP address.
    :for i from=([:len $currentIP] - 1) to=0 do={
        :if ([:pick $currentIP $i] = "/") do={
            :set currentIP [:pick $currentIP 0 $i]

    :log info "No-IP: DNS IP ($previousIP), interface IP ($currentIP)"
    :if ($currentIP != $previousIP) do={
        :log info "No-IP: Current IP $currentIP is not equal to previous IP, update needed"

#       The update URL. The "\3F" is hex for question mark (?). This is required since ? is a special character in the command.
        :local url "http://dynupdate.no-ip.com/nic/update\3Fmyip=$currentIP"
        :local noipHostnames
        :set noipHostnames [:toarray $noipHostname]
        :foreach hostname in=$noipHostnames do={
            :log info "No-IP: Sending update for $hostname"
            /tool fetch url=($url . "&hostname=$hostname") user=$noipUsername password=$noipPassword mode=http dst-path=($logDestination . "no-ip_ddns_update-" . $hostname . ".txt")
            :log info "No-IP: Host $hostname updated on No-IP with IP $currentIP"
    }   else={
        :log info "No-IP: Previous IP $previousIP is equal to current IP, no update needed"

}   else={
    :log info "No-IP: $wanInterface is not currently running, unable to verify and/or update IP."
:log warning message="END: No-IP DDNS Update"

Leave a Comment